All Our Prices Include Standard Postage Worldwide!!
BSA Bantam Related Products

Another Rooster Ignitions ProductBCDI-2

Bantam D5 and D7 Bones CDI Ignition with 12v Alternator

*** Improves reliability, Improves starting, Improves performance, Improves fuel efficiency ***
*** Can be fitted to Direct or Battery equipped machines ***
The Bones CDI Ignition system is a complete ignition and power solution for BSA Bantams.
It includes a CDI ignition module with upto 38 degrees of advance and a 12v Alternator fed to a 12v Regulator Rectifer (included).
More details can be found here.

Please also see our Special Offer BBBKMAX1 12v Halogen and LED bulb + 12v Horn kit to compliment this item.

!! This item is heavy and will incur additional postage charges if delivered outside the UK
Please contact us for a quote !!
£275.00
Another Rooster Ignitions ProductRB1-6P

Rooster Booster RB1 Universal 6V Positive Earth Electronic Ignition Module

This module can be used on most 6v Positive earth motorcycles, cars and other petrol engines fitted with conventional coil and points ignition.
The Rooster Booster is a points assisted electronic ignition system, sometimes refered to as an Energy Booster or Transistor Ignition System. The original engine points and timing advance mechanism (if fitted) are retained, although the condensor is removed completely.

The contact breaker is used purely as a low voltage, low current switch and points errosion is eliminated, meaning no burning or pitting. Contact breaker life should therefore be almost infinite.

This module can be used on most single cylinder petrol engines and multi-cylinder petrol engines equipped with an ignition distributor. It can also be used on 360 degree twin engines if you install a dual output ignition coil using the wasted spark principle.

The system is suitable for Motorcycles, Cars and Commercial Vehicles.

Other benefits also include:-

+ Eliminates the condensor.
+ Can dramatically improve strength and reliability of spark.
+ Can improve hot and cold starting.
+ Smoother running engine and can improve combustion.
+ Eliminates contact breaker erosion (pitting, burning).
+ Greatly reduces ignition system maintenance.
+ Possible fuel economy improvement and lower emissons.

The Rooster Booster has a very simple four wire installation and should the need arise can be uninstalled in minutes. Like most electronic systems, your machine must be correctly operating on its original equipment before fitting.

Please Note: You must have a correctly working voltage regulator to use this module. Some machines were not fitted with any type of regulation and will need to be fitted with either a Regulator Rectifier or a suitable voltage regulator to avoid damage to the module.
£45.00
Another Rooster Ignitions ProductRBJ

Rooster Booster Junior Electronic Ignition Module

The Rooster Booster Junior ignition system is a full electronic ignition system for most engines equipped with a flywheel generator.
This module is extremely popular with owners of the humble BSA Bantam (D1-D7) although it will drastically improve most flywheel generator equipped machines.It is very easy to fit with just two wires and on engines equipped with single magnet flywheels you can remove your contact breaker assembly. In all cases the condensor is eliminated.
Like most electronic systems, your machine must be correctly operating on its original equipment before fitting.

You can view the installation instructions HERE.
£25.00
Another Rooster Ignitions ProductD1D7CK

BSA Bantam D1-D7 Ignition Coil with soldered HT Cable and Spark Plug Cap

This is an extra service we offer with our ignition coils. We can supply the ignition coil with a pre-soldered HT cable and an unsuppressed spark plug cap.
The HT cable and spark plug cap are black.
Please email us with either the Bantam model or the length of HT cable you require.
Please Note: Actual item may be a different colour than the one shown.
£25.50
Another Rooster Ignitions ProductD1D7IC

BSA Bantam D1-D7 Ignition Coil

This ignition coil will fit all BSA Bantam D1-D7 models which the exception of the Lucas model.

We also supply this product complete with an HT lead soldered onto the ignition coil and a non-resistor (un-suppressed) spark plug cap. The HT lead can be cut to your required length and the cost is 28.50
Please contact us for further details

This item replaces the original equipment and can be used with or without one of our electronic ignition modules.
Please note: Actual item may be a different colour from the one shown.
£20.99
Another Rooster Ignitions ProductLCC1

Ignition Coil Clamp for a Lucas MA6/MA12 style igntion coil

Ignition Coil Clamp for a Lucas MA6/MA12 style igntion coil. Fits most standard size single output motorcycle ignition coils.
£5.00
Another Rooster Ignitions ProductRC6-1A

Small Diameter 6V Ignition Coi (40mm)

This is a universal 6v 40mm diameter ignition coil. It is rated at 3 ohms impedance and can be used with a standard contact breaker configuration or with a Rooster Booster electronic ignition system. It has a small metallic housing and measures just 11cm in length with a 4.5cm diameter can. It is easy to fit and is supplied with an electrical fitting kit to suit most installations.
£23.50
Another Rooster Ignitions ProductRMA-6

Standard 6V Ignition Coil (Genuine Lucas MA6)

This is a genuine Lucas branded standard sized 6v, universal oil filled ignition coil.
We also sell seperately a 2 inch coil bracket for this item.

Primary impedance: 1.8 to 2.4 ohms.
Total Length: 5 inches.
Body Diameter: 1 7/8 inches.
£21.00
Another Rooster Ignitions ProductWW19377

Energy Transfer (ET) Ignition Coil

Energy Transfer (ET) Ignition coil for use on Triumph, BSA and other models with batteryless ignition.
This coil can be used for both 6V and 12V points, or CDI/ET ignition systems.
Original Lucas part numbers were LU45149 and LU45150.
£20.50
Another Rooster Ignitions ProductHTC1

1m Copper Core HT Lead (7mm)

1m of high quality 7mm black HT cable made in a modern insulation with a copper core.
£2.50
Another Rooster Ignitions ProductHTL1

HT Cable (7mm) & Spark Plug Cap

1m of Quality Copper Cored 7mm (OD) HT Ignition Cable fitted with an Un-Suppressed (non-resistor) Spark Plug Cap
£5.50
Another Rooster Ignitions ProductPCLIP10

White Nylon Cable P Clip (x10)

Handy white nylon P Clip cable guides to connect wiring to the vehicle frame or chassis.
Easy to fit single bolt or screw mounting.
Supplied in a bag of 10 clips.
£1.25
Another Rooster Ignitions ProductWHBBAC

BSA Bantam D1 (and Others) Direct AC Wiring Harness

This is a wiring loom for a BSA Bantam D1 (and Others) Direct AC (no battery) model motorcycle.
It is designed for both the original Wipac switch with screw terminal connections and the later Wipac SO781/2 type switch. The colour coding and wiring is the same on both machines.
If you are using the later type of switch you can either connect your original switch socket or solder the wires directly to the base of the SO781/2 switch or we can supply a new Wipac SO781/2 socket for you to solder in place (Our Part Number: SO781/2SK2).
£25.00
Another Rooster Ignitions ProductWHD14

Wiring harness - BSA Bantam D10, D14, B175

Genuine Lucas manufactured wiring harness to replace original Wipac loom on a BSA Bantam D10, D14 or B175 battery model.
This quality item is supplied with both Wipac switch sockets connected to the wiring and is ready to fit.
£64.00
Another Rooster Ignitions ProductWHD7DS

Wiring harness - BSA Bantam D7 twin switch

Genuine Lucas manufactured wiring harness to replace original Wipac loom on a BSA Bantam D7 twin switch model.
This quality item is supplied with both Wipac switch sockets connected to the wiring and is ready to fit.
£64.00
Another Rooster Ignitions ProductC-EL1

Condenser with an end fitting lug

Universal condenser as fitted to most British, American, European and Japanese motorcycles
£6.50
Another Rooster Ignitions ProductC-SL1

Condenser with a side fitting bracket (Wipac Bantam etc)

As fitted to Wipac Flywheel Generator Bantams and all BSA Singles from 1968, Triumph TR25 and T140 1973-75 and many others.
£9.00
Another Rooster Ignitions ProductCB1

BSA Bantam D1-D7 Contact Breaker Set (Imported)

These contact breakers fit all BSA Bantam D1-D7 motorcycles with the exception of the Lucas alternator models.

This item is a direct replacement for the original equipment and can be used with or without one of our electronic ignition modules.
£12.50
Another Rooster Ignitions ProductCB2

BSA Bantam D10 - B175 Contact Breaker Assembly (Points)

These contact breakers will fit all BSA Bantam D10, D13, D14, D175 and B175 models.

This item will replace the original equipment and can be used with or without one of our electronic ignition modules.
£9.99
Another Rooster Ignitions ProductBR6HIX

NGK BR6HIX Iridium Spark Plug

Extremely High Quality Iridium Spark Plug found to improve starting and running, with better resistance to whiskering and to be longer lasting. This Spark Plug replaces NGK B6HS, Champion L10 and Champion L86C. It is especially suitable for BSA Bantam D1D2 Machines Prior to 1954. This is a resistor spark plug and you should ensure that your spark plug caps are not suppressed.
£11.50
Another Rooster Ignitions ProductBR7EIX

NGK BR7EIX Iridium Spark Plug

Extremely High Quality Iridium Spark Plug found to improve starting and running, with better resistance to whiskering and to be longer lasting. This Spark Plug replaces NGK B7ES and Champion N4C. It is especially suitable for BSA Bantam D10,D14, D175 and B175 models. This is a resistor spark plug and you should ensure that your spark plug caps are not suppressed.
£11.50
Another Rooster Ignitions ProductBR7HIX

NGK BR7HIX Iridium Spark Plug

Extremely High Quality Iridium Spark Plug found to improve starting and running, with better resistance to whiskering and to be longer lasting. This Spark Plug replaces NGK B7HS, Champion L7, Champion L82 and Champion L82C. It is especially suitable for BSA Bantam D1 after 1954 and D3 & D5 models. This is a resistor spark plug and you should ensure that your spark plug caps are not suppressed.
£11.50
Another Rooster Ignitions ProductL82C

Champion L82C Spark Plug (D1-D7 etc)

We have found that other than Iridium versions, many british machines including BSA Bantams, run better on Champion spark plugs than any other brand.
This is the BSA recommended spark plug for BSA Bantam D1-D7 models manufactured after 1954.
£3.99
Another Rooster Ignitions ProductL86C

Champion L86C Spark Plug (pre 54 D1 etc)

We have found that other than Iridium versions, many british machines including BSA Bantams, run better on Champion spark plugs than any other brand.
This is the BSA recommended spark plug for BSA Bantams manufactured before 1954.
£3.99
Another Rooster Ignitions ProductN4C

Champion N4C Spark Plug (D10-D14-B175 etc)

We have found that other than Iridium versions, many british machines including BSA Bantams, run better on Champion spark plugs than any other brand.
This is the BSA recommended spark plug for BSA Bantam D10, D13, D14 and B175 models.
£3.99
Another Rooster Ignitions ProductSPC1

Lodge Style Rubber Un-Suppressed Spark Plug Cap

Quality Lodge Style Rubber Spark Plug Cap for Classic Motorcycle and Car engines with cable clamp
£2.50
Another Rooster Ignitions ProductSPC2

NGK Branded Un-Suppressed Spark Plug Cap

NGK Branded Rubber Un-Suppressed Spark Plug Cap for Classic Motorcycle or Car engines.
£2.75
Another Rooster Ignitions ProductBA15S1

Quartz Halogen 6v Ba15s 5w Pilot \ Sidelight Bulb

Banish the Prince of Darkess with this 5w Quartz Halogen Tail or Sidelight Bulb in a Ba15s package as fitted to many classic British motorcycles.This Quartz Halogen replacement will produce around 200% the lighting output of the equivilant tungsten bulb. This bulb should also be able to replace original 15w fitments. No modifications are required to fit this upgrade.

At least DOUBLE the brightness of your original tungsten bulbs!
£6.00
Another Rooster Ignitions ProductBA15S2

Quartz Halogen 6v Ba15s 20w Pilot \ Sidelight Bulb

Banish the Prince of Darkess with this 20w Quartz Halogen Tail or Sidelight Bulb in a Ba15s package as fitted to many classic British motorcycles.This Quartz Halogen replacement will produce around 200% the lighting output of the equivilant tungsten bulb. This bulb should also be able to replace original 15w fitments. No modifications are required to fit this upgrade.

At least DOUBLE the brightness of your original tungsten bulbs!
£6.00
Another Rooster Ignitions ProductBA15ST

BA15S 6v 5w Pilot \ Sidelight Bulb

A standard tungsten 6v 5w sidelight \ pilot bulb,
Suitable for most classic motorcycles with a 6v electrical system.
£1.50
Another Rooster Ignitions ProductBA7S6V0.6

BA7S 6V 0.6W Tungsten Speedo \ Instrument Bulb

This is a replacement BA7S 6v 0.6w Speedo\Instrument bulb suitable for many classic British motorcycles.
£1.20
Another Rooster Ignitions ProductBA9S-12-23

Standard 12V BA9S Pilot\Indicator 23W Bulb

This is a tungsted 12v BA9S single filament bulb for use as a pilot (side) light or as an indicator light.
£3.00
Another Rooster Ignitions ProductBA9S-12-L4

T4W LED BA9S White LED Pilot Bulb

This is a negative earth T4W LED Bright White BA9S bulb for use as a Pilot or Instrument bulb.
It only draws around 0.2A from your electrical system!!
This is the equivilant to a standard 15w tungsten bulb.

£3.50
Another Rooster Ignitions ProductBA9S-6V-21

Ultra Bright Halogen BA9S 6V 21W Pilot Bulb

Ultra Bright BA9S Halogen 6V 21W Pilot Bulb.
Can be used in a standard BA9s bulb socket without any other modifications.
£5.00
Another Rooster Ignitions ProductBA9S-6V-2W

BA9S 6V 2W Pilot \ Speedo \ Instrument Bulb

BA9S Tungsten 6V 2W Pilot and Speedo\Instrument Bulb as used on British Motorcycles until 1963
£1.50
Another Rooster Ignitions ProductBA9S-6V-6W

BA9S 6V 5W Pilot \ Speedo \ Instrument Bulb

BA9S Tungsten 6V 6W Pilot and Speedo\Instrument Bulb as used on British Motorcycles until 1963
£1.50
Another Rooster Ignitions ProductBBBKMAX1

12v Super Bright Halogen and LED Bulb Kit + 12v Horn

This is a special offer aimed at customers who buy our Bones CDI systems but open to all customers.
It will fit most BSA Bantams converted to 12v and many other classic machines.
The kit includes a Super Bright Quartz Halogen 35/35w BPF (P36d) Headlight bulb, an LED BA9s Sidelight bulb, an LED BA7s Speedo bulb, an LED BAY15d Tail/Stop/Number Plate bulb and a standard 12v horn.
If your rear light unit has 3 bulbs rather than one, please email us as we may be able to provide LED lighting for this unit as well.
Please note:Your machine must be wired for Negative Earth for this kit. The Bones system can be wired for either Positive or Negative Earth.
We can advise you about changes on any machine should you be in any doubt.
£28.75
Another Rooster Ignitions ProductBMY15D6v21

Tungsten BAY15D 6v 21/3w Stop/Tail rear light bulb

This is a BAY15D 6v 21/3w rear light bulb as used by most classic British motorcycles and it is suitable for all of our Lucas and Wipac rear light units.
£1.50
Another Rooster Ignitions ProductBN15D12L25

Negative LEDACE 12v BAY15D LED StopTail Bulb

This LED 12v NEGATIVE earth bulb can be used to illuminate the Tail, Stop and Numberplate lights.
It only draws 0.3A from your electrical system!!
It has 19 red LEDs facing rearward and 6 radially mounted white that give white numberplate lighting and light up the whole of the lens.
£12.00
Another Rooster Ignitions ProductBP15D12L25

Positive 'Ledace' 12v BAY15D LED Stop\Tail Bulb

This LED 12v POSITIVE earth bulb can be used to illuminate the Tail, Stop and Numberplate lights.
It only draws 0.3A from your electrical system!!
It has 19 red LEDs facing rearward and 6 radially mounted white that give white numberplate lighting and light up the whole of the lens.
£12.00
Another Rooster Ignitions ProductBPFH575

BSA Bantam Headlight Lens Reflector

If your original headlight reflector is flaking and the glass is scratched and dull, replace it with this high quality 5 3/4 lens eflector.
£19.50
Another Rooster Ignitions ProductBPFS-1

BPF Headlight Bulb Socket

If your original headlight bulb holder is rusty and worn or the cabling is brittle and damaged, replace it with this British Pre Focus (BPF) headlight bulb holdersocket. This will ensure a good contact with the bulb and enhance the lighting efficiency. This is a particually good investment if you also purchase one of our other BPF lighting products.
£4.25
Another Rooster Ignitions ProductBPF_STD_1

Standard 6v 35/35w BPF Headlight Bulb

An economy standard 6v 35/35w headlight bulb suitable for many British motorcycles.
Also see our Quartz Halogen upgrqrade replacement bulbs.
£4.99
Another Rooster Ignitions ProductBPF_STD_2

Standard Tungsten 12v 36/24w BPF Headlight Bulb

Standard fitment 12v Bulb supplied in British Pre Focus format also known as BPF or P36d.
This bulb is rated at 36/24 watts.
Brighter halogen versions of this bulb format are also available.
£2.99
Another Rooster Ignitions ProductBQHK-25

BSA Bantam 6v Quartz Halogen Headlight Kit - 25/25w

This is an upgrade 6v Quartz Halogen Headlight Kit for a BSA Bantam or any motorcycle using a 5 3/4 headlight.
The kit includes a 6v 25/25w Quartz Halogen BPF style headlight bulb and a quality headlight lenseflector.
This kit produces around double the brightness of the original tungsten fitment and no modifications are required.
£35.99
Another Rooster Ignitions ProductBQHK-35

BSA Bantam 6v Quartz Halogen Headlight Kit - 35/35w

This is an upgrade 6v Quartz Halogen Headlight Kit for a BSA Bantam or any motorcycle using a 5 3/4 headlight.
The kit includes a 6v 35/35w Quartz Halogen BPF style headlight bulb and a quality headlight lens\reflector.
This kit produces around double the brightness of the original tungsten fitment and no modifications are required.
£33.50
Another Rooster Ignitions ProductH435-12

Halogen 12v H4 (P43t) 35/35w Headlight Bulb

A superbright halogen 12v H4 P43t format bulb.
This item is rated at 35w for main and dipped mode.
This bulb is ideal for our Wipac 5 3/4 inch H4 headlight lens and reflectors or for any machine equipped with H4 type headlight units.
£6.25
Another Rooster Ignitions ProductH4H575

Genuine Wipac 5-3/4 inch Headlight / Reflector

Genuine Wipac combined headlight lens reflector 5-3/4 inches in diameter.
This item has an H4 (P43, P43t) main bulb fitting and a sidelight.
It can be used with either 6v or 12v bulb systems and makes a great upgrade for machines such as the BSA Bantam.
£19.50
Another Rooster Ignitions ProductHBA15DB1

Quartz Halogen 6v 25-25w BA15d Headlight Bulb (Pre BPF)

This is a 6v 25-25w Quartz Halogen Upgraded Headlight Bulb in a BA15d (Pre BPF Bayonet) package as fitted to many classic British motorcycles including early BSA Bantams.
This Quartz Halogen replacement will produce around 200% the lighting output of the equivilant tungsten bulb.
No modifications are required to fit this upgrade.
At least DOUBLE the brightness of your original tungsten bulbs!
£11.50
Another Rooster Ignitions ProductHBA15DB2

Quartz Halogen 12v 35-35w BA15d Headlight Bulb (Pre BPF)

Quartz Halogen 12v 35-35w BA15d Headlight Bulb (Pre BPF)
£11.50
Another Rooster Ignitions ProductHBPF25

Quartz Halogen 6v BPF 25-25w Bulb

Banish the Prince of Darkess with this 6v 25-25w Quartz Halogen Bulb in a British Pre Focus (BPF) package as fitted to many classic British motorcycles.This Quartz Halogen replacement will produce around 200% the lighting output of the equivilant tungsten bulb. No modifications are required to fit this upgrade.

At least DOUBLE the brightness of your original tungsten bulbs!
£12.99
Another Rooster Ignitions ProductHBPF35

Quartz Halogen 6v BPF 35-35w Bulb

Banish the Prince of Darkess with this 6v 35-35w Quartz Halogen Bulb in a British Pre Focus (BPF) package as fitted to many classic British motorcycles.This Quartz Halogen replacement will produce around 200% the lighting output of the equivilant tungsten bulb. No modifications are required to fit this upgrade.

At least DOUBLE the brightness of your original tungsten bulbs!
£10.00
Another Rooster Ignitions ProductHBPF35-12

Quartz Halogen 12v BPF 35-35w Bulb (Special Order)

Banish the Prince of Darkess with this 12V 35-35w Quartz Halogen Bulb in a British Pre Focus (BPF) package as fitted to many classic British motorcycles.This Quartz Halogen replacement will produce around 200% the lighting output of the equivilant tungsten bulb. No modifications are required to fit this upgrade.

Please Note:
This item is a special order and may take upto a week to be dispatched!
£12.50
Another Rooster Ignitions ProductHBPF45-12

Quartz Halogen 12v BPF 45-40w Bulb (Special Order)

Banish the Prince of Darkess with this 12V 45-40w Quartz Halogen Bulb in a British Pre Focus (BPF) package as fitted to many classic British motorcycles.This Quartz Halogen replacement will produce around 200% the lighting output of the equivilant tungsten bulb. No modifications are required to fit this upgrade.

Please Note:
This item is a special order and may take upto a week to be dispatched!
£12.50
Another Rooster Ignitions ProductMES10-12-5

Brake Light or Side Light for Early BSA Bantam and others (MES10) 12V 5W

Tungsten MES10 12V 5W bulb commonly used in motorcycle side lights, car dash panel lights and some Wipac rear brake lights.
£1.50
Another Rooster Ignitions ProductMES10-6-3

Brake Light or Side Light for Early BSA Bantam and others (MES10) 6V 3W

Tungsten MES10 6V 3W bulb commonly used in motorcycle side lights, car dash panel lights and some Wipac rear brake lights.
£1.50
Another Rooster Ignitions ProductPLBH1

Rubber Mounted Motorcycle Pilot Light Bulb Holder (BA9S)

Motorcycle Pilot Side Light Bulb Holder which pushfits into headlight lens reflector using a rubber mounting (supplied).
This item has two wire fitting as used on many British, European and Japanese motorcycles.
It can be used with 6v and 12v BA9S bulbs. - bulb not included.
£4.99
Another Rooster Ignitions ProductPLBH2

Genuine Lucas Cage Mounted Pilot Bulb Holder (BA9S)

Genuine Lucas motorcycle Pilot Side light bulb socket which pushfits into headlight lens reflector using a finger type cage mounting.
This item has one or two wire fitting. The bulb can either be earthed via the metallic backplate of the lens or using the second wire on the holder.This type of fitting is used on many British, European and Japanese motorcycles.
It can be used with 6v and 12v BA9s bulbs. - bulb not included.
£6.99
Another Rooster Ignitions ProductWC1

Genuine Lucas Headlight Rim Clip (W Clip)

Lucas branded headlight rim clips, supplied in a bag of 4 clips.
These are used to secure the headlight lens to the rim in Lucas, Wipac, Miller, Stanley and many other headlight assemblies.
Please note that these are genuine Lucas branded items as it has been found that many unbranded clips do not fit correctly.

£2.50
Another Rooster Ignitions ProductWW19033

Replica Lucas 525 Rear Light Unit

This is a high quality replica Lucas 525 rear light complete rear light unit as used by many British motorcycles between 1953 and 1955
This unit is supplied with a 12v bulb, but a 6v replacement can also be ordered on this page.
£11.50
Another Rooster Ignitions ProductWW19036

Replica Lucas 564 Rear Light Unit

This is a high quality replica Lucas 564 complete rear light unit and bulb.as fitted to many British motorcycles between 1955 and 1970.
It is supplied with a 12v bulb as standard, but 6v replacement bulbs can also be purchaed from this page.
£10.50
Another Rooster Ignitions ProductWW19036/1

Replica Lucas 564 Rear Light Lens

This is a high quality replacement replice Lucas 564 rear light lens.
It does not include the backing fitting or bulb.
£4.75
Another Rooster Ignitions ProductWW19040

Replica Wipac rear lamp for early direct lighting

Replica Wipac rear lamp for direct lighting models.
Single filament (no stop light).
Fits BSA Bantam D1.
£12.00
Another Rooster Ignitions ProductWW19041

Replica Lucas 529 rear lamp

Fitted to many lightweight machines, BSA Bantam,AJS 350/500,Ariel 350,Enfield 250,Velocette and early Triumph T20 Tiger Cubs and Terriers.
Twin Filament type. Supplied with 3 mounting screws
Supplied with 6V stop tail bulb, and british type bullet connectors as standard.
£18.99
Another Rooster Ignitions ProductWW19302

Replica Wipac Series 143(b) Sabrina Rear Lamp Unit

This is a high quality replica Wipac rear light unit as fitted to BSA Bantam D7,D10,D14,B175, C10L, Triumph T20B Super Cub, Ariel Colt models, AJS/Matchless lightweights, Francis Barnett, as well as Sunbeam models.
This rear lamp was also known as Series 143 and Series 143b and when the unit was fitted with a stop and tail lamp in the mid 1960s, Wipac part number S3611. Often also called the Sabrina rear light.
£19.25
Another Rooster Ignitions ProductBR1

Bridge Rectifier

This Bridge Rectifier replaces the square and round plate rectifiers found on most classic motorcycles. The original equipment for these machines will now be past its best and this component will be much more efficient. It is also very easy to fit and is supplied with a diagram.We recommend however that if your machine does not have a voltage regulator, the rectifier is replaced wirh a combined solid state regulator rectifier like the RR6 or RR1.

You can see the wiring diagram HERE.
£3.99
Another Rooster Ignitions ProductF10A-30

10A Glass Fuse - 1.25 inch 30-32mm (x2)

Quick blow glass fuse suitable for most machines with a 1.25 inch fuse holder.
For 6v generators upto 60w and 12v generators upto 120w.
Supplied in a bag of 2.
£1.00
Another Rooster Ignitions ProductF15A-30

15A Glass Fuse - 1.25 inch 30-32mm (x2)

Quick blow glass fuse suitable for most machines with a 1.25 inch fuse holder.
For 6v generators upto 90w and 12v generators upto 180w.
Supplied in a bag of 2.
£1.00
Another Rooster Ignitions ProductF20A-30

20A Glass Fuse - 1.25 inch 30-32mm (x2)

Quick blow glass fuse suitable for most machines with a 1.25 inch fuse holder.
For 6v generators upto 120w and 12v generators upto 240w.
Supplied in a bag of 2.
£1.00
Another Rooster Ignitions ProductF25A-30

25A Glass Fuse - 1.25 inch 30-32mm (x2)

Quick blow glass fuse suitable for most machines with 1.25 inch fuse holder.
Supplied in a bag of 2.
£1.00
Another Rooster Ignitions ProductFH1

Authentic Bakelite Classic Fuse Holder

This item is supplied with a 20A 30mm glass fuse.
It looks and feels like an authentic bakelite fuse holder of the classic era.
Replacement fuses and other fuse current values are easily available.
£2.50
Another Rooster Ignitions ProductRM0752L

Genuine Lucas RM alternator rotor with 0.752 inch mounting

This is a motorcycle alternator 6 pole welded rotor with a 0.752 inch diameter mounting.
This rotor superceeds all other Lucas RM series rotors from the 1950s to the 1970s.
!! This item is heavy and will incur additional postage charges if delivered outside the UK Please contact us for a quote !!
£74.99
Another Rooster Ignitions ProductRM19W

Pattern RM19 alternator stator (3 wire)

This is a pattern (Lucas) RM19 3 wire, single phase alternator stator.
Capable of delivering up to 30V and current up to 20A (Nominal:11.5A) at speeds of up to 10,000 RPM.
Originally used on 6V systems, but also used on the early 12v systems before superseded by the Lucas RM21.
* 6V ~ 83W / 12V ~ 166W *
!! This item is heavy and will incur additional postage charges if delivered outside the UK Please contact us for a quote !!
£135.00
Another Rooster Ignitions ProductRM21L

Genuine Lucas RM21 Alternator Stator (2 wire)

This is a genuine Lucas RM21 alternator stator with 2 wires.
It is a Single Phase device rated at 10A and is capapble of delivering upto 30V at speeds of upto 10,000RPM.
* 6V ~ 72W / 12V ~ 144W *
!! This item is heavy and will incur additional postage charges if delivered outside the UK Please contact us for a quote !!
£69.99
Another Rooster Ignitions ProductRM21W

Patter RM21 alternator stator (2 wire)

This is a pattern Single Phase stator which can be used as a direct replacement for a Lucas RM21.
It is rated at 10.5A and can be used in 6V or 12V systems with the appropriate voltage regulator.
* 6V ~ 75W / 12V ~ 150W *
!! This item is heavy and will incur additional postage charges if delivered outside the UK Please contact us for a quote !!
£67.99
Another Rooster Ignitions ProductRM23L

Genuine Lucas RM23 alternator stator (2 wire)

For those of you with a thirst fpr electrical power this genuine Lucas RM23 is the King of our alternator stators.
It is rated at 16A and can deliver at speeds upto 10,000RPM.
It can be used for 6V and 12V instalations with the appropriate voltage regulator.
* 6V ~ 115W / 12V ~ 230W *
!! This item is heavy and will incur additional postage charges if delivered outside the UK Please contact us for a quote !!
£72.99
Another Rooster Ignitions ProductRM23W

Pattern RM23 alternator stator (2 wire)

This is a pattern replacement alternator stator for the RM23 oem part.
It is Single Phase and rated at 16A and can deliver at speeds upto 10,000RPM. It can be used for 6V and 12V instalations with the appropriate voltage regulator.
* 6V ~ 115W / 12V ~ 230W *
!! This item is heavy and will incur additional postage charges if delivered outside the UK Please contact us for a quote !!
£70.99
Another Rooster Ignitions ProductRR6-150

Regulator Rectifier Single Phase - 6V

This is a universal 6v single phase Regulator Rectifier for most motorcycles. It is rated at 150 watts. It is easy to fit and is supplied with full fitting instructions and wiring diagrams for all BSA Bantam models.
£34.00
Another Rooster Ignitions ProductRW2L-A

Wipac to Lucas Alternator Adaptor

This item is a Rooster Ignitions exclusive and allows Wpac motorcycle alternator to be replaced with a more commonly available Lucas type alternative.
Wipac alternators are no longer available but the Lucas and unbranded Lucas type units are easy to find.
These adaptors fit BSA Bantams from the D10 model onwards and should also fit the Triumph Tiger Cub and many other machines originally equipped with a Wipac alternator.
£21.99
Another Rooster Ignitions ProductWW10045

Run your bike without a Battery!
(Lucas 2MC Capacitor equiv)

This capacitor which is equivalent to the classic Lucas 2MC item and was used by Triumph, BSA, Matchless, Norton and many others, can be used to make most alternator equipped motorcycles start without the need for a battery.
This alteration is used on many trials and racing motorcycles and is simple as the battery is just substituted for the capacitor.
We also sell a suitable sprung mounting bracket (WW26506)
£14.99
Another Rooster Ignitions ProductWW26506

Lucas 2MC Chrome Sprung Mounting Bracket

This is a sprung mounting bracket for a Lucas 2MC Capacitor.
Supplied in racing format, the mounting loop can be bent at 90 degrees to meet the same shape as the road going use on a Norton Commander and others.
We also stock equivalent capacitors to the Lucas 2MC (WW10045A)
£5.99
Another Rooster Ignitions ProductBRAKESW2

Universal Brake Light Switch

Universal stop/brake light switch.
£8.75
Another Rooster Ignitions ProductLU39

Replica Lucas U39 Lighting Switch

This switch has brass screw terminals and was fitted to many British motorcycles such as the BSA M21 and some BSA Bantams.
£15.00
Another Rooster Ignitions ProductS2370

Wipac S2370 Stop Brake Light Switch - BSA Bantam and AMC Lightweights

Replica Wipac S2370 Stop Switch as fitted to BSA Bantam and AMC lightweights.
£20.99
Another Rooster Ignitions ProductS3857

Wipac Ducon Switch Horn Dip Switch - BSA Bantam C15 B33 B40 A10

Excellent chrome wipac replica ducon dip/horn switch OEM S3857 to suit 7/8 handlebars.
Comes complete with wiring (4 wires) and has a chrome surrround with a black horn button and lever.
This can be fitted to a whole array of British Motorcycles.
£16.99
Another Rooster Ignitions ProductS3858

Wipac Tricon Switch Horn Dip Stop Switch - BSA C15 A10 A65

Excellent chrome wipac replica Tricon Horn/ Dip/ kill switch OEM S3858 to suit 7/8 handlebars.
Comes complete with wiring (5 wires) and has a chrome surround.
This can be fitted to a whole array of British Motorcycles.
£16.99
Another Rooster Ignitions ProductSO781

Wipac SO781 Lighting Switch - BSA Bantam, AJS Lightweights, Norton Navigator

Replica Wipac lighting switch S0781.
Fits BSA Bantam D7,D10,D14 models, AJS lightweight singles and Norton Jubilee,Navigator models.
£21.50
Another Rooster Ignitions ProductSO781/2SK1

Wipac SO781/2 Ignition Lighting Switch Socket

Hard to find replacement wiring harness socket for the Wipac SO781/2 switch.
This socket need to be soldered onto wiring tails or directly to your original loom.
It is supplied with a rubber terminal cover so even if your soldering is terrible, it will still look good.
As used on BSA Bantams, Norton, AJS, Matchless and many other machines.
£17.99
Another Rooster Ignitions ProductSO781/2SK3

Custom wired replacemet SO781/2 Switch Socket
(with tails and bullet terminals)

Rooster Exclusive - Not available anywhere else!!!!
This is a replacement wiring harness socket for the Wipac SO781/2 switch, custom wired for your machine.
Supplied with either British 4.7mm or Japanese/European 3.9mm Bullet terminals.
This item will be supplied to you with the correct colour coded wiring tails for your machine.
Once ordered you will need to send us a wiring diagram for your motorcycle or tell us how you would like the socket to be wired and which bullet terminal size you would prefer.
£45.00
Another Rooster Ignitions ProductSO782

Wipac SO782 Ignition Switch - BSA Bantam

Replica quality Wipac SO782 ignition switch suitable for BSA Bantams
£21.50
Another Rooster Ignitions ProductWWSWD008

Universal Chrome Dip Switch

This is a universal chrome handlebar dip switch.
It can be fitted to any make and model of motorcycle.
£8.50
Another Rooster Ignitions ProductBBHN4

BSA Bantam Cylinder Head Nuts (x4)

Cylinder head nuts for the BSA Bantam range of motorcycles.
Supplied in bags of 4 nuts.
£1.99
Another Rooster Ignitions ProductFTP1

Short Fuel Tap (Petcock) - 90° Outlet

Short format fuel tap with a right angle outlet to save space.
Ideal for BSA Bantams and many British, Japanese, European and American others.
This has as standard a metric M10 fuel tank male fitting but is supplied by default with a brass M10 to 1/8 BSP adapter.
If you would like a different adapter, please measure you fuel tank fitting and contact us before ordering.
For reference:
   1/8 BSP has a 9.5mm diameter
   1/4 BSP has a 12.5mm diameter
   3/8 BSP has a 16.5mm diameter
£9.25
Another Rooster Ignitions ProductMCA003A

BSA Bantam D10 Allen Head Bolt Kit

Engine casing bolt kit with Allen heads for the BSA Bantam D10 models.
Kits are available for other motorcycles on request.
£15.00
Another Rooster Ignitions ProductWW89204

BSA Bantam D14/4 & B175 Allen Bolt Kit (BSF)

Engine casing bolt kit with Allen heads for the BSA Bantam D14 and B175 models.
These bolts have BSF thread forms
Kits are available for other motorcycles on request.
£22.50
Another Rooster Ignitions ProductWW89206

BSA Bantam D1-D5 Allen Head Bolt Kit (Whitworth)

Engine casing bolt kit with Allen heads for the BSA Bantam D1-D5 models.
These bolts have Whitworth thread forms.
Kits are available for other motorcycles on request.
£17.99
Another Rooster Ignitions ProductWW89207

BSA Bantam (Late) D7 Allen Head Bolt Kit (BSF)

Engine casing bolt kit with Allen heads for the later BSA Bantam D7 models.
These bolts have BSF thread forms.
The picture shown may not match actual kit for this motorcycle.
Kits are available for other motorcycles on request.
£21.50
Another Rooster Ignitions ProductRH1-12V

Universal 12v Horn

Small 12v universal horn.
70mm diameter in bright zinc plated finish.
Mounting bracket is 80mm in length.
£7.99
Another Rooster Ignitions ProductRH1-6V

Universal 6v Horn

Small 6V Universal Horn.
65mm diameter in bright Zinc plated finish.Features a double hole mounting bracket, with the mounting holes 28mm apart.
Ideal for most classic motorcycles of the 1950s and 1960s.
£7.99
Another Rooster Ignitions ProductRHC1-6

Universal 6v Chrome Plated Horn with Classic Black Centre

Chrome plated 6v Classic Look Horn.
93mm diameter. Mounting bracket is 90mm in length, with a single 8mm mounting hole.
£10.00
Another Rooster Ignitions ProductRHC2-6

Universal 6v Chrome Plated Horn with Classic Grill Front

Chrome plated 6v horn, 100mm diameter. Mounting bracket is 90mm in length.
£11.00
Another Rooster Ignitions ProductWIPACEX

BSA Bantam Flywheel Extractor Tool

Extractor tool to suit BSA Bantams with Wipac S55 ignitions. This is a good quality British made tool and a very useful piece of equipment for the bantam restorer. BSA part number 61-3188.
£17.50
Another Rooster Ignitions ProductBPCWK

BSA Bantam D1-D7 Points Cam Woodruff Key

This is the woodruff key which holds the points cam in place on a BSA Bantam D1-D7.
These are frequently missing or damaged as they are very small.
Restore your timing to where it should be with a new one.
£4.25
Another Rooster Ignitions ProductC-SL1A

Wipac S55 and Genimag Condensor

As fitted to Wipac Flywheel Generator Bantams and all BSA Singles from 1968, Triumph TR25 and T140 1973-75 and many others.
£9.50
Another Rooster Ignitions ProductCB1A

Wipac S55 and Genimag Contact Breaker Set (Imported)

These contact breakers fit all BSA Bantam D1-D7 and Brockhouse Corgi motorcycles with the exception of the Lucas alternator model.

This item is a direct replacement for the original equipment and can be used with or without one of our electronic ignition modules.
£12.50
Another Rooster Ignitions ProductD1D7CKA

Wipac S55 Ignition Coil with soldered HT Cable and Spark Plug Cap

This is an extra service we offer with our ignition coils. We can supply the ignition coil with a pre-soldered HT cable and an unsuppressed spark plug cap.
The HT cable and spark plug cap are black.
Please email us with either the Bantam model or the length of HT cable you require.
Please Note: Actual item may be a different colour than the one shown.
£25.50
Another Rooster Ignitions ProductD1D7ICA

Wipac S55 and Genimag Magneto Ignition Coil

This ignition coil will fit the Wipac S55 and Genimag magnetos found on BSA Bantams and Brockhouse Corgi motorcycles.

We also supply this product complete with an HT lead soldered onto the ignition coil and a non-resistor (un-suppressed) spark plug cap. The HT lead can be cut to your required length and the cost is 28.50
Please contact us for further details

This item replaces the original equipment and can be used with or without one of our electronic ignition modules.
Please note: Actual item may be a different colour from the one shown.
£20.99
Another Rooster Ignitions ProductFW1

Fibre Washer for top of (Bantam) Wipac S55 Points Pivot.

This is not a standard fitment but it does help insulate the points circlip from the contact breaker spring and keep the contact surfaces alignment stable.
£0.30
Another Rooster Ignitions ProductPCS-1

BSA Bantam D1-D7 Points Cover Screws (x2)

A set of points cover screws for the Wipac S55 magneto with countersunk slotted heads.
£1.40
Another Rooster Ignitions ProductPCS-2

BSA Bantam D1-D7 Points Cam Fixing Screw

This is a half inch long cheesehead screw to secure the points cam on a BSA Bantam Wipac S55 Magneto-Generator.

Please note that the scew has a natural steel finish.
£1.00
Another Rooster Ignitions ProductS55BSH

Wipac S55 Crankshaft Bush

Wipac S55 Generator \ Flywheel Magneto centre crankshaft bush \ bearing.
Nearly every Wipac generator we look at requires this item to be replaced. It will require heating and then press fit removal and replacement.
A worn bush will cause inaccurate timing and may lead to the crankshaft becoming permenantly bent.
£5.00
Another Rooster Ignitions ProductS55GMT

BSA Bantam D1 - D7 Wipac Generator HT Lead Grommet

This is a black rubber cable grommet as used on the Wipac S55 Generator.
This item should also fit the Brockhouse Corgi motorcycles fitted with the same generator.
£7.00
Another Rooster Ignitions ProductS55TS4

BSA Bantam D1 - D7 Wipac Generator Terminal Grub Screws (x4)

These are brass slotted generator terminal grub screws suitable for the Wipac S55 generator as fitted to the BSA Bantam D1 - D7 range and the Brockhouse Corgi motorcycle.
Supplied in bags of 4.
They are not suitable for BSA Bantams fitted with the Lucas alternator or the early Wico-Pacy GeniMag generator.
£2.99

Other Products and Developments are already in progress.... watch this space.!